Furnace Service and Repair
If your gas furnace in Naperville, IL is not working it is likely your furnace needs repair or service. At times the fix is simple, other times it is not. Our heating and furnace service technicians have years of experience working on furnaces like yours in Naperville, IL. has service vehicles on call that are fully equipped with the tools and parts necessary to get your furnace back up and operating.
Our furnace repair, furnace service or replacement pricing is very competitive. Our estimates are always firm with no hidden surprises. You can rely on to advise you properly and to do excellent work promptly. Ask us about maintenance agreements for your high efficiency furnace today.
We provide gas furnace service in Naperville, IL
We provide gas furnace repair in Naperville, IL
R Wire Going To Circuit Board Broke Off On Terminal Repaired Wire System Up And Running Recommended Preventive Maintenance On Both Systems.
Katy, G. Naperville, IL
02-24-2022
Furnace Report:
Furnace Report
• Inducer 1.07 @ .98
• Clean Flame Sensor Cleaned Sensor
• Inspect Blower Motor No Issues
• Inspect Wiring No Issues
• Inspect Burner No Rust
• Inspect Orfices For Blockage Cleared All Ports
• Carbon Monoxide Test 0ppm Found
• Inspect Chimney No Issues
• Inspect Pressure Switch Lines No Issues
• Test Sequence Of Operation No Issues
• Inspect Heat Exchanger No Issues
• Check Ignitor No Issues
• Check/replace Filter Air Filter Looks Good
• Test Gas Shut Off No Issues
• Test Thermostat For Proper Operation No Issues
Kristyn, A. Naperville, IL
01-17-2022
Furnace Report:
Furnace Report
• Inducer 1.07 @ .98
• Clean Flame Sensor Cleaned Sensor
• Inspect Blower Motor No Issues
• Inspect Wiring No Issues
• Inspect Burner No Rust
• Inspect Orfices For Blockage Cleared All Ports
• Carbon Monoxide Test 0ppm Found
• Inspect Chimney No Issues
• Inspect Pressure Switch Lines No Issues
• Test Sequence Of Operation No Issues
• Inspect Heat Exchanger No Issues
• Check Ignitor No Issues
• Check/replace Filter Air Filter Looks Good
• Test Gas Shut Off No Issues
• Test Thermostat For Proper Operation No Issues
Kristyn, A. Naperville, IL
01-15-2022
Upon Arrival Discovered Ignitor Operational With No Flame. I Was Able To Remove The Burner Tube To Discover Rust Build-up.
Furnace Report
1st Floor
• Inducer Amps MNF/1.8 - Test/1.52
• Clean Flame Sensor
• Inspect Blower Motor
• Inspect Wiring
• Inspect Burner
• Inspect Orfices For Blockage
• Carbon Monoxide Test
• Inspect Chimney
• Inspect Pressure Switch Lines
• Test Sequence Of Operation
• Inspect Heat Exchanger
• Check Ignitor
• Check/replace Filter
• Test Gas Shut Off
• Test Thermostat For Proper Operation
Furnace Report
2nd Floor
• Inducer Amps MNF/1.8 - 1.50
• Clean Flame Sensor
• Inspect Blower Motor
• Inspect Wiring
• Inspect Burner
• Inspect Orfices For Blockage
• Carbon Monoxide Test
• Inspect Chimney
• Inspect Pressure Switch Lines
• Test Sequence Of Operation
• Inspect Heat Exchanger
• Check Ignitor
• Check/replace Filter
• Test Gas Shut Off
• Test Thermostat For Proper Operation
Tenaye , M. Naperville , IL
11-23-2021
Upon Arrival Discovered The Flame Was Dropping Out While Running. I Removed The Flame Sensor And Cleaned It. I Gave The Unit Full Maintenance.
John , K. Naperville , IL
11-22-2021
Replaced Run Capacitor On Furnace Blower Motor. Replaced And Checked For Proper Operation.
Steven , D. Naperville , IL
09-04-2019
Unit Was Going Off On High Limit. Changed Extremely Dirty Filter
John, A. Naperville, IL
03-29-2019
